Let’s Talk Color: Weft Yarn Color Changes for Rigid Heddle
Changing weft colors always has the potential to leave you with awkward-looking selvedges or bulk, especially when using a rigid-heddle loom without floating selvedges to help keep ends in check! In this post, Whitney explains the techniques she uses when changing color on a rigid heddle, complete with pictures. ~Andrea
Let’s talk color changes.
I’ve made it to the color-and-weave section of The Weaver’s Idea Book, but I have one little “issue.” My selvedges don’t look very nice and the book doesn’t offer much on changing weft yarn color in your weaving. So, I have gone on a journey to figure it out myself. My first stop had to be the “Ask Madelyn” section of Weaving Today. Madelyn pretty much knows everything about weaving.
Her response to this sort of question:
“There is no perfect solution or standardized method that works for every situation (you have to do whatever works best with your weft yarns and the order in which you are using them). If you are sewing with the fabric and will be cutting away the selvedges, it is best to let weft tails just hang at the selvedges (which I’m sure you’d realize). My choice otherwise is this: If there is one basic color that is used very often (or even two or three colors used often), I’d carry them up the selvedges but encircle them with the active weft so they don’t form loops. For colors that are used less often and farther apart, I’d take the tails around a floating selvedge and back into the same shed for both new and old wefts, doing this on opposite sides at each weft change if I were really particular. For fabrics that are relatively fine, such as most tartans, excessive buildup at the edges is usually not a problem.”
I read it and thought, “Yeah, that’s simple! Thanks Madelyn, now my weaving will be perfect.”
It is true that if you are going to be sewing with the fabric that you don’t have to carry the weft yarn up the selvedge and you can let it hang. But I don’t sew, so most likely none of my fabric will be sewn into anything at the present. That leads to the next part of her answer.
How to Change Weft Yarn Color on a Rigid Heddle
First, the encircling of the active weft: this one I can do. If you have two or more colors and are doing a color change ever few rows this is a great technique. With the active color (in my example it’s white), make a loop around the other color(s) (green) so that, when you pull the weft tight and beat, your active color is underneath the other color(s) and not creating any crazy loops at the selvedge. Whether you have to go over or under the inactive colors will vary depending on what side you are weaving on, but the key is to make sure it encircles those colors.
Now, what if one color of weft yarn (we will call it A) is only used sporadically, which can be the case for striped fabric, what should you do? You can cut the color a couple inches and weave it in as Madelyn suggests, except in rigid heddle weaving you don’t have a floating selvedge to wrap around which makes weaving in the next open shed tricky if the end doesn’t wrap around the last warp thread. I usually just wrap it around the last one if it doesn’t already and move on. If you don’t like the look that creates you will have to come up with a different solution.
I also found a little trick that worked, but left some of the color A on my edges. While I was weaving my large section of color before using A again I loosely hung A over the heddle on the edge of my weaving so that it wouldn’t get in the way too much. Then when I came to that edge I would encircle A using the same techniques for encircling listed above. This made it so that when I needed A again it was right where it needed to be. Again, this does leave some color at the edge, but if you don’t mind the effect you might want to give it a try.
I should put a disclaimer that I have no idea if this technique is conventional or “right” BUT if it works do it! Seriously, when it comes to weaving, or any craft for that matter, if you can make something work for you do it. As long as the outcome is what you want and the fabric doesn’t fall apart once you get it off the loom, how you got there isn’t as important. Don’t be afraid to try new things even if others aren’t doing it. You may fail, but that’s the best way to learn.
So, now the question for my readers, have you found a solution for weft yarn color changes that works well for you? Conventional or not, I want to hear them, because I’m sure I will learn some new techniques and have to refine the old!